SiC Diodes, SiC MOSFETs, IGBTs & Power Modules Manufacturer | Hypersemi
TechForum - application notes and selection guides

TECH FORUM

Telecom Power Supply PFC Stage Efficiency Stuck at 96%: Before Replacing the Main Switch, Calculate the Boost Diode Losses First

Telecom Power Supply PFC Stage Efficiency Stuck at 96%: Before Replacing the Main Switch, Calculate the Boost Diode Losses First

      In continuous conduction mode Boost PFC, reverse recovery of the boost diode causes significant reverse-recovery loss and excessive di/dt, generating severe electromagnetic interference. When a silicon fast-recovery diode (FRD) switches from conduction to blocking, stored charge is forcibly extracted, and this energy loss grows as the switching frequency rises. The reverse-recovery charge Qrr of a SiC Schottky diode approaches zero, and the reverse-recovery time can be shortened by about 70%, physically removing the loss penalty of higher frequency. Using a 3 kW PFC with a 400 V bus as a model, from 65 kHz to 100 kHz, the switching-loss savings of SiC are already sufficient to cover the increase in its conduction loss; above 150 kHz, the switching loss of silicon FRD deteriorates sharply, while SiC is almost unaffected by frequency.

  What module packaging provides in telecom power supplies is not 'packaging bare dies,' but turning thermal resistance from an 'estimated value' into an 'input value.'
  When discrete devices are used for PFC Boost, the actual junction temperature depends on PCB copper area, thermal pads, and via arrays, and thermal behavior variation between board lots is difficult to lock down in the early design stage. Module packaging fixes the junction-to-case thermal resistance Rth (j‑c) as a manufacturer-guaranteed and reproducible parameter, so thermal simulation changes from 'guessing PCB heat-dissipation capability' to 'inputting Rth (j‑c) to directly calculate case temperature.' For telecom power supply product lines that require multi-platform thermal design reuse, this difference affects development cycle and first-pass success rate more than a few tenths of a percentage point of per-device loss.

For Telecom Power PFC and Output Rectification, Which Part Number Fits?

  For the high-current path of low-voltage telecom power supply PFC and 48/54 V output rectification, the core parameters and operating-condition alignment of HS8MBRH300N2X100 are: 200 V VRRM / 300 A IFAV / VFM 0.75 V / IFSM 2000 A / M31H package. VFM 0.75 V is a low forward-drop grade among 200 V-class modules, corresponding to operating conditions in which conduction loss accounts for a relatively high share of the output rectification path; 300 A IFAV leaves current margin for single-device or dual-device parallel architectures. The positive temperature coefficient of SiC automatically balances current distribution among parallel branches over thermal cycles, avoiding the thermal-runaway positive feedback of the negative temperature coefficient of silicon FRD in parallel scenarios. For the complete lineup and parameter filtering, see the Schottky module product page.

FAQ

Q: For telecom power supply PFC using SiC Schottky, conduction loss is higher than that of silicon FRD; under what conditions does the net benefit of replacement hold?
  The dominant benefit of SiC comes from eliminating reverse-recovery loss, not from an advantage in forward voltage drop. In the 3 kW/400 V PFC model, the conduction loss of SiC is about 0.5 W higher than that of silicon FRD, but the switching-loss savings are already sufficient to cover this increase above 65 kHz, and at 100 kHz the advantage widens further. It is recommended to use the Qrr of the original silicon FRD and the target switching frequency as inputs for loss breakdown, then compare with the VFM 0.75 V of HS8MBRH300N2X100, and use numbers to lock down the decision boundary.

Q: For dual-device parallel operation of the M31H-packaged HS8MBRH300N2X100, is additional design required for current sharing?
  The positive temperature coefficient of SiC increases the on-state voltage drop as junction temperature rises, transferring current to cooler branches and suppressing thermal runaway by mechanism. However, layout symmetry and drive consistency still affect dynamic current sharing; it is recommended to retain low-value current-sharing resistors as engineering redundancy and to use measured branch current distribution as the verification basis.

Q: Can the module's Rth (j‑c) be used directly to estimate actual junction temperature?
  Rth (j‑c) describes the thermal resistance from die to case, and the manufacturer can guarantee this value; however, the thermal path from case to ambient depends on the user's heatsink mounting method, thermal interface material, and cooling conditions, and must be completed by the designer. The correct use is: use Rth (j‑c) and measured case temperature to back-calculate junction temperature, then use case temperature as the boundary condition for heatsink design, rather than trying to replace complete thermal-chain calculation with a single Rth (j‑c).

Back to top