Industrial Power Supply N+1 Redundant Parallel Silicon Schottky: Can Positive Temperature Coefficient Enable Self-Current Sharing?
A frequent engineering pitfall is transplanting the self‑balancing merit of SiC Schottky diodes onto silicon‑based Schottky devices. Silicon Schottky diodes feature negative temperature coefficient of forward voltage VF. When paralleled, positive thermal‑feedback makes hotter dies draw higher current, creating thermal‑runaway risks. Hypersemi HS8MBRH Schottky modules cannot alter this intrinsic silicon‑device characteristic.
1. Inherent Risks of Parallel Silicon Schottky: Dual Positive Feedback from Negative VF‑TC and Reverse Leakage
In N+1 redundant industrial power‑supply rectifiers, multiple devices are paralleled for current sharing. Silicon Schottky diodes exhibit a typical forward‑voltage temperature coefficient of approximately −2 mV/℃. In parallel branches, hotter devices show lower VF, draw higher forward current and get even hotter, establishing self‑reinforcing positive thermal feedback.
Meanwhile, reverse saturation leakage current IS of silicon Schottky diodes rises exponentially with junction temperature. Hot devices suffer elevated conduction loss as well as increased blocking loss, squeezing overall thermal budget. Even with tightly pre‑screened matched VF values, an initial VF spread as small as 0.1 % will evolve into severe current imbalance within several thermal time constants.
Ballast resistors are widely adopted to counteract current drift by adding external impedance, at the cost of extra conduction loss and higher PCB layout complexity. Parallel schemes that solely rely on VF bin‑sorting without external current‑sharing measures carry considerable field‑failure risk.
2. Engineering Approach of HS8MBRH Series: No Promise of Self‑Sharing, but Quantifiable Thermal Boundaries
Hypersemi HS8MBRH Schottky‑module portfolio covers package options M01G, M31H, M45, M58. Continuous forward‑current ratings span 100 A‑800 A with non‑repetitive surge current from 800 A‑6400 A. Target applications include high‑frequency SMPS, electroplating power supplies, inverter welders and variable‑frequency drives.
Category page: https://www.hypersemi.com.cn/cn/products/schottky-modules
Two widely‑used M31H‑package variants for parallel applications:
HS8MBRH200N2X100: 200 V / 200 A / 1 V / IFSM 1650 A, suitable as basic building block in parallel arrays.
Product page: https://www.hypersemi.com.cn/cn/products/schottky-modules/HS8MBRH200N2X100.html
HS8MBRH400N2X100: 200 V / 400 A / 0.95 V / IFSM 3300 A. Higher per‑module current rating within identical M31H footprint reduces branch count and eases overall current‑sharing challenges.
Product page: https://www.hypersemi.com.cn/cn/products/schottky-modules/HS8MBRH400N2X100.html
Modular packaging brings three documentable physical benefits for parallel design:
1. Junction‑to‑case thermal resistance Rth(j‑c) is clearly specified in datasheets, so junction‑temperature calculation no longer depends on guesswork over internal package construction;
2. Symmetric internal die layout minimizes initial thermal unbalance among paralleled chips inside one module;
3. Standardized mechanical mounting interfaces enable explicit thermal‑coupling modelling among multiple modules in thermal simulation workflows.
3. Three Non‑Negotiable Ground‑Rules for Silicon Schottky Parallel Design
① External current‑sharing network cannot be omitted. Negative temperature coefficient is intrinsic for silicon Schottky diodes. Low‑value ballast resistors (typically below 0.1 Ω) serve as secondary protection. Accept moderate extra conduction loss to improve current distribution at power‑on and during transients; self‑current‑sharing cannot be assumed.
② PCB traces shall be equal‑length and symmetric. At high‑frequency commutation, mismatch of parasitic inductance among branches creates initial current offset. The negative‑temperature‑coefficient effect amplifies such imbalance instead of correcting it. Copper trace length, width and via configuration for parallel branches shall be kept as identical as practical.
③ Thermal coupling between modules must be explicitly included in thermal simulation. Physically adjacent modules mutually heat each other. Such “thermally‑coupled proximity” aggravates over‑current in the hottest device and degrades the effectiveness of ballast networks. This effect must be evaluated during simulation phase.
4. Frequently Asked Questions
Q: What is the fundamental parallel‑sharing difference between silicon Schottky and SiC Schottky diodes?
A: They feature opposite forward‑voltage temperature‑coefficient polarities. Silicon Schottky VF drops when temperature rises (negative TC), creating thermal positive feedback; external current‑sharing countermeasures are mandatory for parallel operation. Under high‑current operating conditions, SiC Schottky diodes show rising VF with increasing temperature (positive TC), delivering inherent current self‑balancing capability. Design practices proven for SiC SBD must not be copied directly onto silicon Schottky designs. HS8MBRH are silicon‑based Schottky modules; all parallel design work shall start from silicon‑device negative‑temperature‑coefficient characteristics.
Q: For N+1 redundant parallel systems: how to choose between HS8MBRH200N2X100 and HS8MBRH400N2X100?
A: Trade‑off lies between branch quantity and current‑sharing complexity. The 200 A variant needs more parallel branches for the same total output current, raising workload for current‑sharing network and thermal‑coupling management. It fits moderate total‑current applications requiring fine‑grained expandability. The 400 A variant offers higher per‑module current within the M31H package, reducing branch count and simplifying sharing schemes for high‑current rectifier arms. Conduction‑loss comparison should not rely merely on 25 ℃ room‑temperature VF; joint loss calculation combining target case temperature and datasheet‑specified Rth(j‑c) is required.
Q: How does surge‑current rating of paralleled Schottky modules influence selection during N+1 redundancy switching events?
A: Transient current upon redundancy switching is determined by load profile and impedance of remaining active branches. IFSM surge rating provides transient‑stress margin. More critically, steady‑state current through surviving modules after switching shall not exceed their derated continuous‑current capability. The 200 A and 400 A HS8MBRH grades offer 1650 A and 3300 A surge respectively. Device rating selection shall be based on steady‑state current under N‑1 fault condition, to guarantee controllable thermal boundaries after fault switching.