SiC Diodes, SiC MOSFETs, IGBTs & Power Modules Manufacturer | Hypersemi
TechForum - application notes and selection guides

TECH FORUM

N+M Parallel PSU Light-Load Current-Sharing Misconception: Positive VF Temperature Coefficient Is Not a Guarantee—the ZTC Point Is the Key Selection Criterion

N+M Parallel PSU Light-Load Current-Sharing Misconception: Positive VF Temperature Coefficient Is Not a Guarantee—the ZTC Point Is the Key Selection Criterion

SiC Schottky VF’s positive temperature coefficient and natural suitability for parallel operation **hold only above the zero temperature coefficient point (ZTC)**. Server power N+M redundancy often runs modules at 30%–50% of rated current or lower light load, easily below ZTC in negative coefficient: higher junction temperature lowers VF, current concentrates in hot devices, risking thermal positive feedback. First check actual light-load current vs. ZTC, not VF.

1. ZTC Point: Critical Boundary Determining Parallel Current‑Sharing Behaviour

  Forward voltage VF of Schottky diodes is jointly governed by the barrier‑height term and drift‑region resistance term. At low current, the barrier term dominates. Rising temperature reduces barrier height more significantly than carrier‑mobility degradation, causing VF to drop with temperature, showing negative temperature coefficient.

  As current rises, drift‑region resistance takes over. Lattice‑scattering effects become stronger, VF increases with rising temperature and exhibits positive temperature coefficient. The current value at which these two behaviours cross is defined as the ZTC (Zero‑Temperature‑Coefficient) point.

  Above ZTC point: Hotter devices show higher VF; current transfers toward cooler dies and natural current‑sharing occurs.
  Below ZTC point: Hotter devices show lower VF; current concentrates on hotter dies, establishing positive thermal‑feedback loop: junction‑temperature rise → VF drop → higher current → higher loss → further junction‑temperature increase.

  SiC Schottky diodes feature lower ZTC point compared with silicon PiN diodes and deliver better thermal convergence under mismatched thermal boundary conditions. Meanwhile, this property extends the negative‑temperature‑coefficient region toward higher‑current levels, making light‑load / low‑duty‑cycle operation more susceptible to current‑sharing degradation.

2. Server‑PSU Load Profile Exposes ZTC‑Related Engineering Risks

  Real‑world data‑centre PSUs seldom run continuously at full load. IT‑load fluctuations, standby rotation of redundant units and low‑utilisation night‑time operation frequently force individual parallel modules to operate at 30%‑50% rated current or less.

  Under such conditions, the oversimplified statement “SiC Schottky has positive VF temperature coefficient for natural parallel sharing” cannot be directly adopted. Designers must refer to datasheet VF‑Tj curves and compare actual operating current against ZTC‑point current.

  If ZTC‑point current is higher than practical light‑load operating current, thermal positive‑feedback risk is not merely theoretical but represents real reliability hazard under field mission profiles.

3. Module Packaging Reduces Parallel Variables, But Does Not Replace ZTC Verification

  For paralleled discrete devices, each die junction temperature behaves independently. ZTC behaviour inside multi‑chip power modules results from combined effects of chip consistency, baseplate thermal coupling and package thermal resistance.

  Two Hypersemi high‑power non‑isolated Schottky modules:
  HS8MBRH300N2X100: 200 V / 300 A, typical VF=0.75 V, IFSM=2000 A, M31H non‑isolated SBD

Product page: https://www.hypersemi.com.cn/cn/products/schottky‑modules/HS8MBRH300N2X100.html

  HS11UDA800N2X100: 200 V / 800 A, typical VF=0.95 V, IFSM=6400 A, M45 non‑isolated SBD

Product page: https://www.hypersemi.com.cn/cn/products/schottky‑modules/HS11UDA800N2X100.html

  Both modules undergo factory‑side thermal‑characteristic matching of internal chip‑sets to reduce the quantity of parallel branches requiring manual oversight. Non‑isolated construction removes thermal resistance contributed by insulation layers between baseplate and heatsink, which benefits thermal convergence for high‑density PSUs. However, this advantage is only valid after completing ZTC‑point validation; package properties cannot be relied upon to eliminate ZTC‑related risks.

4. Frequently Asked Questions

Q1: Can SiC Schottky diodes be operated in parallel?

A: Parallel operation is feasible, yet performance strongly depends on operating‑current range. When operating current sits above ZTC point, positive temperature coefficient dominates and natural current‑sharing works. Below ZTC point thermal positive feedback prevails. Designers shall apply parallel derating factors or adjust hardware branch design according to the gap between practical operating current and ZTC‑point current.

Q2: Should selection prioritise nominal VF or ZTC‑point check?

A: First determine real‑world operating‑current range derived from mission‑profile analysis, then judge whether this range lies above or below ZTC point. Low nominal VF does not guarantee reliable light‑load parallel performance. Some devices show attractive VF specifications but have ZTC point higher than light‑load operating current — exactly the high‑risk combination for thermal positive feedback.

Q3: What ZTC‑check differences exist between module‑based versus discrete‑device parallel designs?

A: Parallel discrete devices demand junction‑temperature and ZTC evaluation for every single part. Power modules consolidate multi‑chip thermal coupling and consistency at package level; verification scope shrinks from many discrete dies down to module‑level assessment. Nevertheless, chip‑to‑chip current imbalance still exists within modules; final judgement must be based on datasheet VF‑Tj characteristic curves.

Q4: Which Hypersemi parts suit secondary rectification / OR‑ing paths inside N+M parallel PSUs?

A: Within the 200 V portfolio, HS8MBRH300N2X100 targets branches with 200‑250 A continuous current where low VF plus 2000 A surge margin are desired. HS11UDA800N2X100, with 800 A rating and 6400 A surge capability, addresses higher‑power‑density parallel branches. Both adopt M‑series non‑isolated packages. Full‑product‑selection page: https://www.hypersemi.com.cn/cn/products/schottky‑modules.

Q5: Does device‑selection conclusion change if light‑load conditions dominate mission profile?

A: Yes. If 30%‑50% light‑load occupies large weight within mission profile, prefer devices with documented ZTC‑point parameters in datasheets whose light‑load operating range falls within positive‑temperature‑coefficient region. Relying merely on the generic claim “SiC Schottky exhibits positive VF temperature coefficient” leaves thermal‑runaway hazards present in end‑equipment field deployment.

Back to top