The efficiency ceiling of industrial UPS and high-end PFC often comes down to a single Boost diode
Efficiency in industrial UPS and high-end PFC designs often plateaus at 94%–95%, with limited gains from repeated main-switch iterations. The overlooked variable is the reverse-recovery loss of the Boost diode. SiC Schottky diodes remove this constraint by their unipolar carrier nature, but “switching to SiC” is not an unconditional win.
1. The Hidden Source of the Efficiency Plateau: Boost Diode Reverse Recovery
In industrial UPS and high-end PFC designs, the trend toward 65 kHz and even 100 kHz switching frequencies is well established. Main switches have progressed from silicon superjunction MOSFETs to SiC MOSFETs, yet efficiency remains stuck in the 94%–95% range. The problem is often not the switch itself, but the Boost diode in the PFC stage.
When a silicon fast-recovery diode (FRD) transitions from forward conduction to reverse blocking, minority carriers stored near the PN junction are forcibly swept out, creating a reverse-recovery current spike. This spike acts on both the diode and the commutating main switch, and the loss scales linearly with switching frequency. The higher the frequency, the harder this energy cost becomes to avoid.
SiC Schottky diodes are unipolar carrier devices. They do not inject minority carriers during forward conduction, so there is no stored charge to sweep out at turn-off. Their reverse-recovery charge Qrr is negligible, and reverse-recovery loss approaches zero.This is not a marginal efficiency improvement; it removes the loss barrier to higher frequency at the physical-mechanism level.
2. Loss Accounting: At What Frequency Does the SiC Benefit Take Hold?
SiC is not universally superior to silicon FRD in PFC. The forward voltage of SiC Schottky is typically higher than that of a silicon FRD at the same current class, creating an increment in conduction loss after replacement. For a 3 kW double-conversion online UPS with a 400 V PFC bus and an average diode current of approximately 4.2 A, the SiC conduction loss is about 0.5 W higher than the silicon FRD.
The key decision is not “whether SiC saves energy,” but whether the absolute reverse-recovery loss at the target switching frequency is significantly greater than the conduction-loss increment. Published measurements provide a clear boundary: at 100 kHz, a circuit using a SiC diode achieves 98.7% efficiency versus 98% for the silicon counterpart; at 200 kHz the SiC advantage widens further, and at 400 kHz the loss is 46% lower.From 65 kHz to 100 kHz, the total-loss advantage of SiC is already established. Above 150 kHz, the reverse-recovery loss of the silicon FRD deteriorates sharply, while SiC is far less sensitive to frequency.
In other words, frequency is the first decision variable. If the target switching frequency remains below roughly 30 kHz, the conduction-loss increment may offset the reverse-recovery savings. Once the design enters the 65–100 kHz range, the SiC benefit begins to dominate.
3. Selection Entry Point for High-Voltage Bus PFC: 1700 V SiC Module
The high-voltage bus after PFC from a three-phase 400/480 V industrial grid requires a blocking voltage covering the 1700 V class. CG80SD170S2X100 lists PFC and UPS directly among its applications on the HyperSemi datasheet. Its core parameters are 1700 V blocking voltage, 80 A continuous current, SOT-227 package, and typical on-resistance (VF) of 1.45 V.The SOT-227 industrial-standard mounting interface means replacement evaluation on an existing UPS power board does not require redesigning the heatsink mechanical structure, lowering the engineering barrier for migrating from silicon to SiC.
4. A Comparison Option for Low-Voltage High-Current Paths: 200 V Schottky Module
For high-current paths in 200 V-class low-voltage PFC or DC-DC output rectification, HS8MBRH300N2X100 offers another topology entry point. In the M31H package, it provides 300 A forward current, 200 V blocking voltage, 0.75 V forward voltage, and 2000 A surge current.The M31H package has an established adaptation base in variable-frequency equipment and high-frequency switching power supplies, making it suitable for low-voltage rectification positions with clear requirements on forward drop and surge tolerance.
A fuller range of SiC Schottky and silicon Schottky modules can be located on the Schottky module selection page by voltage, current, and package.