SiC Diodes, SiC MOSFETs, IGBTs & Power Modules Manufacturer | Hypersemi
TechForum - application notes and selection guides

TECH FORUM

Industrial Power Supplies Burning Rectifier Diodes in the Field: The Problem Is Often Not the Rated Current

Industrial Power Supplies Burning Rectifier Diodes in the Field: The Problem Is Often Not the Rated Current

A large share of field failures of rectifier devices in industrial power supplies are not caused by undersized steady-state current ratings, but insufficient surge withstand capability and voltage clamping margin. Engineering review cases show that a front-end anti-reverse silicon Schottky diode selected for adequate steady-state current suffered direct breakdown and short-circuit when exposed to ±2 kV surge at power-on, with peak current exceeding 8 A.

1. Typical Failure Mode: Good Steady‑State Rating, Over‑Stressed by Transients

  Industrial power supplies differ from consumer‑grade units because they must survive real‑world transient energy from grid disturbances and load changes. Lightning surges, load‑dump events, transformer‑leakage spikes and voltage overshoot induced by PCB parasitic inductance can push rectifier diodes toward avalanche stress within microsecond‑to‑millisecond timescales.

  In one documented case, a 1 A‑rated 1N5819 Schottky operated with less than 1 A steady‑state input current, seemingly well‑rated. Yet surge events generated peak currents above 8 A, exceeding its surge capability and causing immediate destructive short‑circuit failure.

  Avalanche robustness and peak forward‑surge current I_{FSM} are often not highlighted on datasheet front pages, yet they determine system survivability under rare extreme events. For AC‑DC front‑end rectifiers and inductive‑load freewheeling branches, checking only nominal average forward current I_{FAV} and repetitive reverse voltage V_{RRM} is insufficient. Designers must incorporate measured or simulated peak‑current waveforms, voltage‑spike amplitudes and repetition frequency into derating calculations.

2. Margin Design of HS8MBRH400N2X100: 200 V Blocking Voltage and 3300 A Surge Capability

  Hypersemi’s Schottky‑module portfolio at 200 V blocking voltage covers average currents from 200 A to 800 A, with non‑repetitive surge ratings ranging 1650 A‑6400 A. HS8MBRH400N2X100 is a non‑isolated Schottky module: 200 V V_{RRM}, 400 A I_{F(AV)}, 0.95 V typical V_{F}, 3300 A I_{FSM}, housed in M31H package. Target applications include high‑frequency SMPS, electroplating power supplies, inverter welders and variable‑frequency drives.

Product page: https://www.hypersemi.com.cn/cn/products/schottky-modules/HS8MBRH400N2X100.html

  Its 3300 A surge rating delivers more than 8× transient‑current margin relative to the 400 A continuous average current. One frequently misunderstood point: silicon‑based Schottky diodes exhibit negative temperature coefficient of forward voltage V_{F}. As junction temperature rises, V_{F} drops. Unlike SiC Schottky diodes with positive temperature coefficient, silicon Schottkys do not self‑balance when paralleled; hotter devices tend to draw more current, creating positive thermal‑runaway feedback riskROHM.

  The M31H package cannot eliminate this intrinsic silicon‑Schottky physical characteristic. Its value lies in making junction‑to‑case thermal resistance R_{th(j‑c)} a well‑specified, calculable datasheet parameter. Symmetric internal die layout also reduces initial V_{F} spread among paralleled chips. High‑current thermal design changes from bin‑sorting discrete parts plus passive current‑sharing resistors toward simulation‑verifiable, repeatable engineering workflows. For N+1 redundancy and expandable parallel architectures, this design determinism matters more than purely matching nominal datasheet values.

3. Three‑Step Reliability‑Oriented Selection Checklist

  ① Surge‑current validation: Use measured or simulated peak‑current waveforms as input. Read I_{FSM} derating curves corresponding to actual pulse width in datasheets. Do not simply scale the standard 8.3 ms half‑sine surge rating by arbitrary multipliers. Surge withstand depends heavily on pulse duration and initial junction temperature; ratings for different pulse widths are not directly interchangeable. For welding or electroplating equipment subject to repeated shocks, evaluate cumulative thermal‑fatigue effects from recurring surges.

  ② Blocking‑loss calculation at maximum junction temperature: Compute blocking loss using reverse‑leakage current I_{R} at maximum operating junction temperature. Reverse leakage of silicon Schottkys rises steeply with junction temperature. Blocking loss can become a non‑negligible portion of total power dissipation under high‑temperature conditions; do not rely solely on 25 ℃ nominal leakage values.

  ③ PCB‑level co‑validation of protection networks: Verify placement and trace length for TVS or clamping networks. Long traces introduce parasitic inductance, raising real‑world voltage spikes arriving at the rectifier far above simulation predictions.

4. Frequently Asked Questions

Q: What surge‑current margin factor I_{FSM} should be used for industrial rectifier selection?

A: There is no universal multiplier. Required margin depends on surge‑pulse duration and repetition rate. Use measured or simulated current waveforms and refer to datasheet derating curves for the actual pulse width. For equipment enduring repetitive shocks (welders, electroplating power supplies), account for lifetime degradation from cumulative surge stress. For rare lightning‑surge events, apply safety factors against single‑pulse peak values. HS8MBRH400N2X100’s 3300 A surge rating provides substantial transient buffer, yet final margins must be derived from real‑application waveforms.

Q: Since leakage current rises sharply with temperature, can high‑temperature operation erase the efficiency benefit of low V_{F} for Schottky devices?

A: This represents a genuine constraint for silicon Schottkys in hot industrial environments. Reverse leakage increases steeply with junction temperature, raising blocking‑loss share. Continuous maximum junction temperature for conventional silicon Schottkys is generally limited to approximately 90 ℃. Compare total loss as: Total Loss = V_{F}@Tj(max) × I_{F} + V_{R} × I_{R}@Tj(max) instead of evaluating only room‑temperature V_{F}. Hypersemi datasheets provide leakage‑versus‑temperature curves to quantify net low‑V_{F} benefit under target case‑temperature conditions.

Q: How to choose between HS8MBRH400N2X100 and the 300 A sibling model?

A: The trade‑off lies between conduction loss and surge‑withstand margin. HS8MBRH300N2X100 features lower 0.75 V typical forward voltage, favouring applications dominated by steady large continuous current for reduced conduction loss. HS8MBRH400N2X100 with higher 3300 A surge rating offers greater safety margin where surge stress and inductive turn‑off spikes dominate. Both use the M31H package with pin‑to‑pin layout compatibility; final selection can be confirmed by prototype‑stage waveform measurement.

Back to top