SiC Diodes, SiC MOSFETs, IGBTs & Power Modules Manufacturer | Hypersemi
TechForum - application notes and selection guides

TECH FORUM

Home appliance PFC switching frequencies are usually not high, so the high-frequency advantages of SiC MOSFETs cannot be leveraged—is it still necessary?

Home appliance PFC switching frequencies are usually not high, so the high-frequency advantages of SiC MOSFETs cannot be leveraged—is it still necessary?

The answer is Yes—and the necessity has already been validated by mass-production data. What SiC MOSFETs reduce at low switching frequencies is not a “frequency dividend,” but hard-switching commutation losses and high-temperature conduction losses: the tail current of silicon devices consumes energy fixedly in every switching cycle, whereas SiC turn-off has no tail current; at the same time, silicon’s RDS(on) rises to about 1.6 times its room-temperature value at 110°C, while SiC barely increases, so the gap in full-load conduction loss is further widened in a real thermal environment. Gree’s SiC chips have already been installed and shipped in more than 2 million air conditioners, and the reduced temperature rise and improved energy efficiency are reproducible system-level benefits, not theoretical projections.

At low switching frequencies, what exactly does SiC save?

The switching-device losses of a CCM boost PFC consist of four parts: conduction loss, turn-on loss, turn-off loss, and body-diode reverse recovery. In the 20–50 kHz range, the latter three are locked onto a relatively high baseline by the physical characteristics of silicon devices—IGBT tail current prevents turn-off loss from disappearing as frequency decreases, and the Qrr of silicon fast-recovery diodes is fixedly converted into heat under hard-switching commutation.

The change brought by SiC MOSFETs is structural. There is no minority-carrier tail, so the turn-off process is clean; body-diode reverse-recovery charge is extremely low, so commutation loss shrinks substantially from the loss budget. An itemized loss breakdown of a 300 W boost PFC shows that at a 100 kHz switching frequency, the total switching-device loss of the SiC solution is about 2.294 W, versus about 5.404 W for the silicon solution—a reduction of about 42%. This gap does not hold only at 100 kHz—at lower frequencies, the absolute value of frequency-related switching loss decreases, but the share of conduction loss and reverse recovery increases, and SiC’s advantage in high-temperature RDS(on) becomes even more dominant.

The mass-production data disclosed by Gree grounds this logic in a specific product: SiC SBDs are used in the PFC circuit of a residential 3-HP air conditioner, and at 220 V input, efficiency is improved by 0.5% and device temperature rise is reduced by 10°C compared with the silicon-based solution. A 10°C difference in temperature rise directly means the heatsink can be smaller, thermal stress inside the sealed control box is reduced, and long-term reliability is improved. This is the most honest value statement for SiC in low-switching-frequency home appliance scenarios.

Selection entry point: the “matching logic” of CM65R065LX100

The typical DC bus voltage of a home appliance PFC is in the 380–420 V range. A 650 V rating leaves reasonable margin for switching overshoot while avoiding the extra conduction-resistance and cost penalties of 1200 V devices. Hypersemi’s CM65R065LX100 (650 V / 38 A / 65 mΩ, TO-247-3L) provides, on this voltage platform, a loss and current-carrying combination suitable for the main switch of a 2–3 kW-class home appliance PFC. Product details page: https://www.hypersemi.com.cn/cn/products/sic-mosfets/CM65R065LX100.html

The absolute value of 65 mΩ on-resistance is limited at PFC currents of a few amperes, but what really deserves attention during selection is the high-temperature RDS(on) retention rate. As mentioned earlier, silicon devices’ on-resistance rises to 1.6 times at 110°C, while SiC has very small temperature drift; this means that when the actual junction temperature inside the control box approaches 100–125°C, the conduction-loss increase of CM65R065LX100 is far smaller than that of a silicon solution with the same nominal resistance, and the “25°C nominal value” is retained more fully in a real thermal environment. The TO-247-3L package, meanwhile, is the heatsink and layout platform most familiar to home appliance power supply teams, and the migration cost centers on gate-resistor tuning and reliable turn-off drive rather than topology redesign.

Back to top